HELP!!!

I ran the Avast! Scan and the report is as follows:

07/12/2009 14:11
Scan of all local drives

File C:\System Volume Information_restore{728F5C67-ED43-4A61-8E72-7822AF7B58BE}\RP119\A0060654.EXE is infected by Win32:Rootkit-gen [Rtk], Deleted
File C:\System Volume Information_restore{728F5C67-ED43-4A61-8E72-7822AF7B58BE}\RP125\A0066543.EXE is infected by Win32:Rootkit-gen [Rtk], Deleted
File C:\System Volume Information_restore{728F5C67-ED43-4A61-8E72-7822AF7B58BE}\RP137\A0074927.EXE is infected by Win32:Rootkit-gen [Rtk], Deleted
File C:\WINDOWS\system32\4D27AB\shell.fne is infected by Win32:Trojan-gen {Other}, Repair: Error 42060 {The file was not repaired.}, Repair: Error 42060 {The file was not repaired.}, Deleted
Number of searched folders: 15035
Number of tested files: 158551
Number of infected files: 4

After the scan, I can only go to the desktop. Then, there is a blue screen and my computer restarts automatically. What should I do?

If you cant access your desktop anymore since the PC keeps restarting. Boot into Safe Mode. From there, schedule an avast Boot Time Scan.

If you can get into Safe Mode, change the Recovery Settings so you can read what error message the BSOD is giving you.

Post the message here.

You could also try booting into Last Known Good instead of Safe Mode.

Recovery Settings

One of the things that is quite different about Windows XP compared to Windows 9x (9x is shorthand for Windows 95, Windows 98, and Windows Me in all their various versions), is that one can control how it responds to certain critical errors—those that cause the infamous Blue Screen of Death (BSOD). In Windows XP, the default setting is for the computer to reboot automatically when a fatal error occurs. If that fatal error only occurs when you’re shutting down, the system reboots automatically.

If you haven’t changed any of the system failure settings, you should be able to see the error by looking in the Event Log. But a better long-term solution is to turn off the automatic reboot so you can actually see the error when it happens—chances are it will tell you enough about itself to let you troubleshoot further. To change the recovery settings to disable automatic rebooting:

Right-click My Computer, and then click Properties.

Click the Advanced tab.

Under Startup and Recovery, click Settings to open the Startup and Recovery dialog box.

Clear the Automatically restart check box, and click OK the necessary number of times.

Restart your computer for the settings to take effect.

http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/russel_02may13.mspx

The blue screen reads as follows:

A problem has been detected and windows has been shut down to prevent damage to your computer.

The problem seems to be caused by the following file: LVPrcMon.sys

If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow theses steps:

Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you may need.

If problem continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced options, and then select Safe Mode.

Technical Information:

*** STOP: 0x000000D4 (0xBAC41410, 0x00000002 , 0x00000000 , 0x80536622)

LVPrcMon.sys

Beginning dump of physical memory
Physical memory dump complete.
Contact your system administrator or technical support group for further assistance.

Missed out the following line:

The driver unloaded without cancelling pending operations.

Update your Logitech QuickCam software:
http://forums.logitech.com/logitech/board/message?board.id=quickcam_software&thread.id=58970

Thanks. But I do not know the part number or anything of the cam as it is part of my laptop. An integrated cam. How do I go about doing it then? Thanks.

The blue screen may be caused by :
registry error
physical memory error
hardware failure

for registry error, you can download a registry cleaner software such as registryeasy from http://www.jj54.com/ an clean the errors.

for physical memory error, you should shutdown the computer ,and pull out the memory card and re-plugin. and then restart the computer.

Try device manager:

http://www.annoyances.org/exec/show/article01-420

Or a system information utility:

http://www.snapfiles.com/Freeware/system/fwsysteminfo.html