I think it should be:
accept = 127.0.0.1:12110
I think it should be:
servername - 127.0.0.1
As far I can understand…
Dear Collegue! I find some think nuance with statical and dinamycal IP adress and stunnel and TB…
Dear SergFon - I wrote little article (Russian) in this link - http://forum.sukhoi.ru/showthread.php?t=45299 - please, if this information is interest to Avast, please translate it and add it in Faq or other themes about avast and ssl…I didn’t find information about difference setup IP and DHCP adress to Stunnel and TB on our forum… Thank everybody very match!
Who is avast resseler in Saint-Peitrsburg, Russia? Give me contact infoirmation…I want suggest our CEO about futured our corprate antivirus system 
I wish Alan could give us some light here…
It’s a pity that we can’t alert him by IM anymore 
Tech,
I am not sure which Alan you mean.
However, this Alan is very puzzled at the introduction of DHCP vs static IP into this issue.
I will admit, again, that I have never used STunnel but this is just the plain old proxy issue with STunnel being the proxy. I am very familiar with testing Thunderbird and various proxy chains with avast involved and I have reported on a number of them in this forum. I find it hard to imagine how IP addresses are involved.
Thunderbird works in no way different from any other mail client (they all have to work the same way since they are all implementing the old as dirt POP and SMTP protocols).
My last Russian lessons were almost 40 years ago and I last tested my Russian speaking ability in St. Petersburg (it had a different name at the time) 30 years ago. So, I doubt that I will have much success in reading the discussion that has been mentioned.
Dear Moderators, U suggest final resume In FAQ this questions…
For correct work and scanning email with SSL connection on depend type of TCP address getting for local IP avast must has nest setting…
If yours host get DHCP address from DHCP server the setting of ThunderBird and stunnel if you have SSL mail connection have standard parametrs descripioned in official FAQ
Stunnel
[gmail-pop3s]
accept = localhost:12110
connect = pop.gmail.com:995
delay = yes
TB
servername - localhost
username - nickname@gmail.com
Port - 12110
after this setting we added to redirecting ports port 12100 and avast normally scanning incoming email
[b]
Important…
If you have statical IP adress, no DHCP you must write next setting to stunnel and TB - you replace localhost to yours staticla IP address
stunnel
[gmail-pop3s]
accept = 10.126.1.2:12110
connect = pop.gmail.com:995
delay = yes
TB
servername - 10.126.12
username - nickname@gmail.com
Port - 12110
after this setting we added to redirecting ports port 12100 and avast normally scanning incoming email for statical IP… In another setting yours TB willn’t correct when you turn avast… I spent some hours, and solve this problem
I didn’t understand mean this sentense…
In my case, when I have local statical IP adress I have problem with redirect ports from SSL to standart POP ports and TB and avast cooperative working…
In other place, where is DHCP IP addresing order - TB + Stunnel + avast work very nice with setting from FAQ…You understand difference statical and dynamical IP?
Dear adminstarion!
Please don’t get newbie the bad pictures and text in profile - I am not lamer…
OK?
Click the Profile button at the top of every page, there you can change your ‘Forum Profile Information’ there, Personal Text: change to I’m a llama (It isn’t lamer) there are no pictures in a Newbies Profile unless you add one, see image.
It stands llama - not lamer
llama → http://www.ansi.okstate.edu/breeds/other/llama/llama1.jpg
But as DavidR told you, you can change the text to whatever you want
Vadim Mc, извини, слишком много текста для перевода, я просто не располагаю таким количеством свободного времени. :-
(Vadim Mc, I’m sorry. The article is too big and I don’t have much time to tramslate it :-).